Clearone-comm XAPTM 800 Bedienungsanleitung Seite 93
- Seite / 149
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
87
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix B: Pinouts
Appendix B: Pinouts
RS-232 COM DCE port pinout (female)
Pin Number Control Pin Number Control
1 DCD 6 DSR
2 TXD 7 CTS
3 RXD 8 RTS
4 DTR 9 No connection
5 Ground
1
5
6
9
Figure B.1. RS-232 connector
PC
XAP 800
DB-9
Male
DB-9
Female
TXD (Pin 2)
RXD (Pin 3)
DTR (Pin 4)
GND (Pin 5)
CTS (Pin 7)
RTS (Pin 8)
TXD (Pin 2)
RXD (Pin 3)
GND (Pin 5)
CTS (Pin 7)
RTS (Pin 8)
Pin 6
Pin 9
Pin 4
Pin 1
Pin 9
Pin 6
Pin 1
XAP 800
Modem
Pin 3
Pin 2
Pin 3
Pin 7
DB-9
Male
DB-25
Female
Pin 5
Pin 2
AMX
XAP 800
TXD (Pin 2)
RXD (Pin 3)
GND (Pin 5)
RX2 (White)
TX2 (Red)
GND (Black)
DB-9
Female
Phoenix
Connectors
CTS (Pin 7)
RTS (Pin 8)
RTS2 (Green)
CTS2 (Blue)
AMX
Modem
DB-25
Female
DB-9
Male
TXD (Pin 2)
RXD (Pin 3)
GND (Pin 5)
CTS (Pin 7)
RTS (Pin 8)
DTR (Pin 4)
TXD (Pin 2)
RXD (Pin 3)
RTS (Pin 7)
GND (Pin 6)
RTS (Pin 20)
CTS (Pin 4)
GND (Pin 5)
Figure B.2. XAP 800 to PC RS-232 connections
Figure B.3. XAP 800 to Modem RS-232 Connections
Figure B.5. Modem to AMX RS-232 Connections
Figure B.4. XAP 800 to AMX RS-232 Connections
ClearOne recommends that
all nine pins be connected to
avoid communication errors.
!
- XAP 800 Installation and 2
- Operation Manual 2
- ClearOne Part No. 800-151-101 2
- July 2002 (Rev. 3.1) 2
- Table of Contents 3
- CHAPTER 1: Introduction 7
- New Features 8
- Unpacking 10
- Front panel 10
- Controls and Connections 10
- Rear panel 11
- Networking 13
- Expansion bus 13
- CHAPTER 2: Installation 15
- To connect the unit 16
- Expansion bus connections 17
- Networking Units 17
- Device IDs 18
- Mixer mode 18
- LCD menu tree 19
- LCD Programming 19
- System menu 20
- RS-232 menu 21
- Meter menu 22
- Inputs menu 23
- Outputs menu 24
- CHAPTER 3: System 27
- Configuration 27
- Creating Floppy Disk Copies 28
- To install G-Ware 28
- Installing G-Ware 28
- Site Setup 29
- Creating a new site 29
- Adding a XAP 800 30
- Configuring Unit Properties 31
- Flow Screen 33
- G-Ware Screens 33
- Copying and pasting settings 34
- Safety Mute 34
- Status bar 34
- Matrix Screen 35
- Expansion bus O–Z routing 36
- Process A–H routing 36
- Cross point attenuation 36
- Audio Routing 36
- Matrix report 37
- Inputs 1–8 38
- Inputs and Outputs 38
- P Pwr (Phantom Power) 39
- Figure 3.29 40
- Virtual Reference 40
- Non-linear Processing (NLP) 41
- Active Filter 41
- Activation 44
- Chairman Override 44
- Adaptive Ambient 44
- PA Adaptive Mode 44
- Gate Ratio 45
- Hold Time 45
- Off Attenuation 45
- Ambient Level 45
- Decay Rate 45
- PA Adapt and AEC Reference 46
- Gating Group Select 47
- Max adjust 48
- Min adjust 48
- Figure 3.42. Gain 48
- Pre Gain 49
- Post Gain 49
- Post Processing 49
- Post Gating 49
- Inputs 9–12 50
- Outputs 1–12 52
- Figure 3.49 53
- Output gain adjust 53
- From Expansion Bus O–Z 54
- To Expansion Bus O–Z 54
- Expansion Buses 54
- Processing A–H 55
- Processing 55
- Cmprs (compressor) 56
- Figure 3.56. Delay window 59
- Figure 3.57. Process 60
- CHAPTER 4: Advanced 61
- Preset Configuration pane 62
- Figure 4.4. Preset Mask 63
- Control/Status B 63
- To create a preset 65
- Storage space 65
- Running presets 66
- Room combining example 67
- Creating macros 69
- Figure 4.16 Macro Name window 70
- Figure 4.14 70
- Macro Editor button 70
- Editing macros 71
- Running macros 72
- CHAPTER 5: Operation 73
- Document Compare Utility 74
- Operation ~ Utilities 75
- Copying settings 76
- Print Reports 77
- GFirm Firmware Utility 78
- G-Ware Switcher 80
- Copy and paste settings 80
- Message Log 81
- Gate View 81
- Monitoring Views 81
- Meter Views 82
- CHAPTER 6: Control 83
- XAP IR Remote 84
- Remote Builder 84
- ClearOne Control Panels 85
- Control ~ Remote Builder 86
- To program the Volume panel 86
- To program the Select panel 87
- Remote Modem Access 88
- Serial commands 88
- RS-232 Port 88
- Command strings 89
- APPENDICES 91
- Appendix B: Pinouts 93
- Control/Status connectors 94
- Control/Status B port pinout 95
- Set connector pinout 96
- Line connector pinout 96
- Connecting the Control Panel 97
- Appendix C: Control Panel 97
- Control Panel Assembly 98
- Dimensions (both versions): 98
- 1.8˝/4.6cm W x 4.125˝ 98
- Appendix D: Accessories 99
- Conventions 100
- Command structure 100
- Appendix E: Serial Commands 100
- Groups and channels 101
- Type and device IDs 101
- Serial command error codes 102
- Meter type definitions 102
- XAP 800 Serial commands 103
- AAMB - Adaptive Ambient Mode 105
- AGC - Automatic Gain Control 105
- AMBLVL - Ambient Level Adjust 106
- BAUD - Baud Rate 107
- COMPRESS - Compressor Adjust 108
- COMPSEL - Compression Select 108
- DECAY - Decay Adjust 109
- DELAY - Delay Adjust 109
- DELAYSEL - Delay Select 109
- DFLTM - Default Meter 110
- DID - Device ID 110
- DSPVER - DSP Version 110
- FILTER - Filter Adjust 111
- FILTSEL - Filter Select 112
- FLOW - Flow Control 112
- FMP - First Mic Priority Mode 112
- FPP - Front Panel Passcode 113
- GAIN - Gain Adjustment 113
- GATE - Gate Status 114
- GHOLD- Gate Hold Time Adjust 114
- GMODE - Gating Mode 115
- GOVER - Gating Override 115
- GRATIO - Gate Ratio Adjust 115
- GREPORT - Gate Report 116
- GRPSEL - Gating Group Select 116
- LABEL - Label 116
- LFP - Lock Front Panel 117
- LMO - Last Mic On Mode 117
- LOCK - Preset and Macro Lock 117
- LVL - Level 118
- LVLREPORT - Level Report 119
- LVLRRATE - Level Report Rate 119
- MAX - Maximum Gain Setting 120
- MDMODE - Modem Mode 121
- MIN - Minimum Gain Setting 121
- Argument details 122
- MLINE - Mic/Line Adjust 123
- MPASS - Modem Password 123
- MTRX - Matrix 124
- MUTE - Mute 125
- OFFA - Off Attenuation Mode 126
- PAA - PA Adaptive Mode 127
- PP - Phantom Power 127
- PRGSTRING - Program String 128
- RAMP – Ramp Gain Adjustment 129
- SERECHO - Serial Echo 130
- SERMODE - Serial Mode 130
- SFTYMUTE - Safety mute 131
- SIGGEN - Signal Generator 131
- STRING - String Execution 132
- TOUT - Time Out Select 133
- UID - Unit ID 133
- VER - Version 133
- Appendix F: Warranty 134
- FCC Part 15 Compliance 136
- Safety Information 136
- Appendix G: Compliance 136
- Glossary 137
- AEC settings 33–35 146
Verwandte Produkte und Handbücher für Musikinstrumente Clearone-comm XAPTM 800
(145 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern